uwu

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 83 total)
  • Author
    Posts
  • in reply to: Miqobot DPS Tier List #20652

    uwu
    Participant
    0

    S tier: MCH BRD
    MCH gets the edge because you literally dont have to do anything. BRD needs to babysit level 80 ability once every 30 secs or so when the bar fills up. You also lose some DPS on brd in fights that have low HP adds because it applies dots that might only tick for 1-2 gcds instead of shooting them.
    Both can achieve Orange parses with the right gear.

    in reply to: Holmister Switch Run-times #20511

    uwu
    Participant
    0

    uwu how are you not dying on trash packs as a BLM? Don’t you just run right in the middle of them and get rekt?

    only saw 1 death on the log. healers keep me up

    in reply to: Holmister Switch Run-times #20475

    uwu
    Participant
    0

    Left my parser running for 15 runs as BLM. Fastest time was 27:10, slowest was 31:11 because it looks like I died to Tesleen. This is using Urianger, Thancred, and Ryne. Most runs were ~28min.

    Actually all of the lowest 27min runs were on Scenario mode with Exarch/Alphinaud/Alisaie

    DPS Numbers:
    Me ~7500
    Alisaie ~3400
    Exarch ~2100
    Alphinaud ~1400+~800
    Ryne ~3500
    Thancred ~2100
    Urianger ~1600

    • This reply was modified 4 years, 8 months ago by  uwu.
    • This reply was modified 4 years, 8 months ago by  uwu.
    • This reply was modified 4 years, 8 months ago by  uwu.
    • This reply was modified 4 years, 8 months ago by  uwu.
    in reply to: Shadowbringers 5.58 – Issues & Feedback #20422

    uwu
    Participant
    2+

    i am having the same issue. Completely deleted off my PC

    in reply to: (Request) Sublime Solution #20281

    uwu
    Participant
    0

    you need to have a macro created to HQ the item and replace it in my scenario or have one named “White Scrips” for it to work correctly

    Also look at the notes and change the corresponding number in the recipie to match what the turn in is for the day. 3,4,5 represents INT DEX OR STR depending

    You need to make sure you have certain actions bound to keys as well, if it not working correctly make sure the following have the correct assinments:

    F12 – Target nearest NPC/Object
    NUM0 – Confirm
    NUM8 – Move cursor up/Cycle through party list
    NUM6 – Move cursor/Target Right
    NUM9 – Cycle through UI Components Forward
    NUM4 – Move cursor/Target Left
    NUM. – Cancel

    • This reply was modified 4 years, 8 months ago by  uwu.
    • This reply was modified 4 years, 8 months ago by  uwu.
    Attachments:
    You must be logged in to view attached files.
    in reply to: BLM vs SAM for Miqobot #20280

    uwu
    Participant
    1+

    SAM is amazing you only have to manage a couple things

    in reply to: Holmister Switch Run-times #20265

    uwu
    Participant
    1+

    Ive run holminster on every job and have every npc at level 80 there is a 0% chance you can run through this in 20 mins. Its literally impossible.

    in reply to: Holmister Switch Run-times #20250

    uwu
    Participant
    0

    Yes just make a 2 chapter scenario. First one is to set the number of dungeons you want to run before repairing, the 2nd will have a repair() followed by a repeatAll(x) where x=number or times you want the scenario to repeat. Just put 99 if you want it to keep going

    chapter 1
    squadrons(5)
    dungeon(Holminster)
    fullClear(on)
    openCoffers(on)

    chapter 2
    repair()
    desynthList(Dungeon)
    desynth()

    repeatAll(99)

    • This reply was modified 4 years, 8 months ago by  uwu.
    • This reply was modified 4 years, 8 months ago by  uwu.
    in reply to: Firmament gather + auto turn in #18878

    uwu
    Participant
    0

    I actually replaced the grid with an updated version someone made. Here is the most current version I have been using.

    Attachments:
    You must be logged in to view attached files.
    in reply to: Firmament gather + auto turn in #18758

    uwu
    Participant
    0

    Default presets I have to allow menu movement under the keybind menu:

    System Tab:

    Num0 – Confirm
    Num2 – Move Cursor Down
    Num8 – Move Cursor UP
    Num* – Display Subcommands
    Num4 – Cursor Left
    Num6 – Cursor Right

    Targeting tab:

    f12 – target nearest NPC

    in reply to: [request] new skybuilder grid! #18746

    uwu
    Participant
    0

    Thats sad to hear because the Miqo custom macros are the greatest part of the bot. You can synth 200 items in a row if you want without paying attention. Just need to map the key presses one time

    in reply to: Chiaroglow/Scuroglow request #18745

    uwu
    Participant
    0

    its in the index i believe or search. There are 2 diff ones out there. a FSH one and a BTN/MIN one

    in reply to: Firmament gather + auto turn in #18741

    uwu
    Participant
    0

    Correct. You need to create and name a macro that you want Miqo to use when synthing. The name goes in the (xxx) where mine says Ishgard i think

    in reply to: Shadowbringers 5.58 – Issues & Feedback #18733

    uwu
    Participant
    0

    You have to manually sendkey() the key strokes. I have a scenario with the sequence, based on default numpad controls of 0 for enter 8/2/4/6 to navigate u/d/l/r and * to select item.

    in reply to: Firmament gather + auto turn in #18710

    uwu
    Participant
    0

    I had to edit a couple chapters because it was crashing, split 8 into 2 diff chapters. This will sometimes get messed up with a lot of lag. Ive used it now to test turning in 100 items and it did work. Def WIP tho.

    Attachments:
    You must be logged in to view attached files.
Viewing 15 posts - 16 through 30 (of 83 total)