Forum Replies Created
-
Posts
-
Would you please give us more information about your issue?
- What does Miqobot say in the Output Area when the freezing occurs?
- How long does Miqobot freeze for? For example, if you leave her freezing for 1 minute does anything else happen?
- Does this issue occur with both Macro Crafting and Solver Crafting?
- Could you please verify that you have all the important keybinds in place, by following our guide on Keybinds and Icons Recognition.
Here is the list of important keybinds that are used in crafting:
– [System] Confirm
– [System] Cancel
– [System] Display Subcommands
– [System] Move Cursor Up
– [System] Move Cursor Down
– [System] Move Cursor Left
– [System] Move Cursor Right
– [System] Cycle through HUD Components (Forward)
– [Movement] Previous Page
– [Movement] Next Page - Could you please confirm that Crafting Log is recognized correctly by Miqobot.
Open Monitor tab, switch mode from “main” to “crafting”, and look for the line that says “Crafting Log: + or -“.
Please make a screenshot of Monitor tab when Crafting Log is opened in the game and attach here.
Thank you very much!
The hotfix for this issue and for identification of Company Workshops is implemented in Miqobot v1.2.632.
Please redownload the latest version from our website, if you need it.As this is a minor upgrade, it will not trigger “new version available” notification.
Company workshops and mission area in Kugane are now supported by Miqobot v1.2.632.
Please redownload the latest version from our website, if you need it.As this is a minor upgrade, it will not trigger “new version available” notification.
Several hotfixes are implemented in Miqobot v1.2.632. Please redownload the latest version from our website.
As this is a minor upgrade, it will not trigger “new version available” notification.
The following problems were addressed:
– General: An issue wherein Miqobot would not identify company workshop zones.
– General: An issue wherein Miqobot would not identify certain quest zones.
– Crafting: An issue wherein crafting would accidentally stop due to incorrect identification of materials in Crafting Log.Thank you for reporting again!
This issue has been already discussed here: Stormblood 4.0 – Miqobot StatusAs we said earlier, Miqobot was not tested with 61+ content and may perform unpredictably. We are doing our best to implement the necessary upgrades as soon as possible.
Thank you for your patience and understanding!
The items under assist box are gathering presets.
They work similar to fishing presets.First select the desired settings, press “New” button, and all your settings are saved into preset. After that you can quickly switch between presets with a single mouse click.
If you want to make adjustments to your preset, first select it, change the desired settings, and press “Overwrite”.Gathering presets are a very recent addition, so they don’t have a dedicated guide section yet.
But they follow the same rules described under Fishing Presets.Thank you for confirming the issue!
Your second problem, about “Blackout”, means that Miqobot did not recognise the current zone and it triggered an internal kill switch. This is a safety measure against drawing unwanted attention in certain cases.
However 01A9 is a code for Company Workshop, and it happened simply because we overlooked workshops.
It will also be fixed in the next minor release.Yes, we are aware of this problem.
Observe cost has been significantly reduced in Stormblood 4.0. It may lead to very long crafting rotations which result in better quality output at the cost of time.We are researching the new crafting math and the necessary adjustments are planned for Upgrade Stage 2.
In the meantime, please remove Observe from your hotbar if you want to prevent this behaviour.Thank you for your feedback!
Btw is Mooch II supported at the moment or no?
No, all new fishing skills are planned for Stormblood Upgrade Stage 2.
Thank you for your patience very much!Yes, as we already said earlier, new gathering skills are planned for Stormblood Upgrade Stage 2.
Thank you for your patience very much!Could you please be more specific about your issue?
- What is the exact message that you see?
We need to know the exact phrasing to identify the problem. Please make a screenshot if possible. - What does Miqobot say in the Output Area at this moment?
- Does it happen when you are AFK? Or does it happen when you watch Miqobot working in background?
- Does Miqobot stop completely when it happens? Or does she continue crafting when you click the message away?
In case Miqobot stops completely, does she continue crafting without issues after pressing Start?
The more information we have, the faster we’ll be able to help you 🙂
Thank you very much!No, Miqobot supports only single jump to fly method.
This is stated directly at our website under Quick Setup:1. Character Configuration -> Mouse Mode (not Gamepad Mode).
2. Character Configuration -> Movement Settings -> Legacy Type (not Standard Type).
3. Character Configuration -> Flying Mount Takeoff -> Auto: Take off on jump.Double jump to fly is considered but not planned in the near future.
At the moment we focus on fully functional upgrades for Stormblood, but we will try to include additional research into development plans later.Thank you for your request!
You don’t have to assign a hotkey for each skill directly, but you have to make sure that they are reachable by keyboard. In short, there must be a keybind for each icon on first hotbar and a keybind to switch to any other hotbar.
For details please read our guide on Keybinds and Icons Recognition.If you follow these simple rules, then yes, Miqobot will use specialist skills.
