Forum Replies Created
-
Posts
-
I’ve tried sitting here just staring at my screen, not running anything else, not touching anything, barely breathing as I obsessively watch Miqobot go through the scenario instructions after reaching the Scrip Exchange NPC, and even when it initially gets to the correct Category for buying the tokens before it can go to the correct Subcategory tab, it keeps going back and changing the Category tab to either Gear or Materia and the whole chapter just gets essentially thrown out the window.
I’m not sure what the heck is wrong- if it’s maybe some sort of lag on my end, or what. I’m kinda sad that this is leaving me little choice but to babysit the scenario for the Only Gathering & Turn In Collectables, manually stop it when my orange tokens get full, and manually buy the tokens. I’ll do it because there seems to be no other option for me at this point, but I dunno, I’m just frustrated, I guess. Been a long day.
-
This reply was modified 2 months ago by
CaffeinatedGremlin.
-
This reply was modified 2 months ago by CaffeinatedGremlin.
I do not, yet- but, do you prefer fishing for it or gathering with MIN/BTN? You can gather some ephemeral nodes with both BTN & MIN or you can fish for some specific fish.
I’m planning to try to make a grid or scenario for gathering the ephemeral nodes since my fishing’s not quite leveled just yet, personally. If I get around to that, I’ll definitely post it for folks to share in the bounty. 🙂
Make sure you’re not interacting with the game at all. Something as simple as moving your mouse can steal focus away from what it’s trying to do, and wind up causing an error.
So, I can’t even have a different window for, say… my internet browser open and watching a movie on that or work on a document, while this scenario runs? That’s disappointing, but if it is the case, I guess I’ll have to unearth my other computer and use that to run Miqo & FFXIV while I use this one for doing other things while Miqobot runs in the background.
I just had another thought, Bubula456. Do you have ‘Use Compass’ checked under the ‘Senses’ section on the ‘Gathering’ tab in Miqobot? That should also help Miqobot register other nodes on the grid, nearby.
I try to make sure the only beacon on my grids is placed right in the center of the area where the relevant nodes spawn. There are typically three (3) clusters of nodes scattered around that area, and each is connected to the beacon in the center of the gathering location, so it can get to all of them- plus, interconnected flight points along the grid at each of the three clusters.
I’m sorry to hear that, Bubula456. Could you provide me the Miqobot log so I can try to see where the issue is?
Also, which navigation grid are you having this issue with? I don’t recall setting more than one (1) beacon per grid, but if I know which navigation grid is giving you this problem, I can take a look at it to make sure.
Screenshots of the waypoint it’s getting stuck on would also be helpful, but not as necessary as the Miqobot log and the name of the grid.
-
This reply was modified 2 months, 1 week ago by CaffeinatedGremlin.
Hey there! This sounds like fun. I’d be glad to lend a hand. I’ll see what I can pull together in the next few days- not sure what time frame you’re looking at staying within, for this, but I’ll have limited time to do much later today (Wednesday) and less time on Thursday, and I have family coming to visit for a local festival Fri-Sun, but I can chip away at this and see how far I get in helping out on this.
The issue I’m having with this is that it gets all the way through just fine- until it reaches the Scrip Exchange NPC and then, it initiates the dialogue that will open the exchange window, but then it scrolls down to select ‘Nothing’ and then, it just sort of selects the NPC a few times, as it goes through the ‘sending key: num#: delay: 1.00 sec’ bit and then it moves on to the next chapter in the Scenario without ever actually buying the tokens it’s supposed to… :/
I’m not sure how to fix this. I’m not savvy enough yet. Any assistance would be appreciated.
(4:52:04 AM) Destination reached!
(4:52:04 AM) Turning camera to angle: 0.92
(4:52:05 AM) Sending key: ‘num0’ (Delay: 2.00 sec)
(4:52:07 AM) Sending key: ‘num0’ (Delay: 2.00 sec)
(4:52:09 AM) Sending key: ‘num0’ (Delay: 3.00 sec)
(4:52:13 AM) Sending key: ‘num8’ (Delay: 1.00 sec)
(4:52:14 AM) Sending key: ‘num0’ (Delay: 1.00 sec)
(4:52:15 AM) Sending key: ‘num8’ (Delay: 1.00 sec)
(4:52:16 AM) Sending key: ‘num0’ (Delay: 1.00 sec)
(4:52:18 AM) Sending key: ‘num2’ (Delay: 1.00 sec)
(4:52:19 AM) Sending key: ‘num0’ (Delay: 1.00 sec)
(4:52:20 AM) Sending key: ‘num8’ (Delay: 1.00 sec)
(4:52:21 AM) Sending key: ‘num0’ (Delay: 1.00 sec)
(4:52:23 AM) Sending key: ‘num8’ (Delay: 1.00 sec)
(4:52:24 AM) Sending key: ‘num8’ (Delay: 1.00 sec)
(4:52:24 AM) (SCENARIO) Stopping…
(4:52:24 AM) (SCENARIO) Stopped.
(4:52:24 AM) Well, you know, I don’t mind continuing it any time! 😉EDIT: I just tried it again and it got the exchange open alright, but it missed the correct Token Category. I’m not sure what’s going on. :/
-
This reply was modified 2 months, 3 weeks ago by CaffeinatedGremlin.
-
This reply was modified 2 months ago by
